02 Settings
Configuration · Preferences · Calibration
2.1 — Language
2.2 — System Defaults
2.2.1 Bowler Hand — setting your default (RH / LH)
2.2.1 setting The Bowler Hand default setting controls whether new bowler profiles and new spe...
2.2.2 Grip Type — Finger Tip vs. Conventional as default
2.2.2 default The Grip Type setting controls which grip style is pre-selected when you create ...
2.2.3 Display in Decimal vs. Fraction (0.000 vs. fractions)
2.2.3 display The Measurement Display setting controls whether span, oval, bridge, and depth m...
2.2.4 Oval Degree Increments — 1° vs. 5° increments
2.2.4 display The Oval Degree Increments setting controls the step size of the degree selector...
2.2.5 Insert Installation — STD vs. VACU grip default
2.2.5 default The Insert Installation default controls which installation method is pre-select...
2.2.6 Vacu Installation Increment from O.D. (1/32, 1/16…)
2.2.6 default When fitting a bowler with VACU Grip inserts, Spectre Cloud calculates the two h...
2.2.7 Display Measurements in your preferred denominator
2.2.7 display When entering a span measurement on a spec sheet, Spectre Cloud presents a dropd...
2.2.8 Display Pitches by your preferred denominator
2.2.8 display When entering a pitch value on a spec sheet, Spectre Cloud presents a dropdown l...
2.3 — Thumb Hole Preferences
2.3.1 Default Hole Type — Round vs. Oval
2.3.1 KEY setting The Default Hole Type setting controls which hole type is pre-selected whe...
2.3.2 Initial pitch inside the total oval — Edge vs. Center & Pitch Included Yes/No
2.3.2 oval When drilling an oval hole, Spectre Cloud needs a reference point from which to cal...
2.3.3 Oval Width Calculator — Bit Size, Decimal, or Difference input method
2.3.3 oval When calculating an oval thumb hole, Spectre Cloud needs to know the oval width — t...
2.3.5 Oval Cut 'Move' Direction — V/H, H only, V only, or None
2.3.5 oval The Oval Cut Move Direction setting controls which directional components Spectre C...
2.3.6 Flip V/H on oval cuts — matching your drill press DRO display order
2.3.6 oval The Flip V/H on oval cuts setting controls the display order of the vertical and ho...
2.4 — Drill Press Calibration
2.4.1 Does your machine display Right Pitch Positive? (YES / NO)
2.4.1 calibration Different drill presses use different sign conventions when displaying pitch...
2.4.2 Does your machine display Forward Thumb Pitch Positive? (YES / NO)
Does your machine display Forward Thumb Pitch Positive? (YES / NO) 2.4.2 calibration Just ...
2.4.3 Display +/- in pitch tiles — showing polarity to match DRO's to avoid errors
2.4.3 calibration Even with sign conventions correctly configured in 2.4.1 and 2.4.2, a raw + ...
2.5 — Layout Preferences
2.5.1 Default Layout Type — VLS, 2LS, PAL, or NONE
Default Layout Type — VLS, 2LS, PAL, or NONE 2.5.1 layout The Default Layout Type setting con...
2.5.2 Default Dual Angle Degree Increments — 1° vs. 5°
2.5.2 layout When entering drilling angle and VAL angle values in a Dual Angle layout, Spectre...
2.6 — Auto-Suggestions
2.6.1 Overview — why leaving all Auto-Suggestions ON saves time
2.6.1 TIP auto Spectre Cloud includes a suite of auto-suggestion features that automatically...
2.6.2 Pitch Suggestion — auto forward pitch based on hand flexibility
2.6.2 auto The Pitch Suggestion setting controls whether Spectre Cloud automatically recommend...
2.6.3 Auto-CLT — lateral pitch of fingers based on CLT chart
2.6.3 auto Center Line Tilt (CLT) is the reference chart Spectre uses to set the lateral pitch...
2.6.4 Auto-Populate Lateral Pitches
2.6.4 auto The Auto-Populate Lateral Pitches is another time saving auto-suggestion for Spectr...
2.6.5 Autofill Bridge
2.6.5 auto The Autofill Bridge setting controls whether Spectre Cloud automatically populates ...
2.6.6 Autofill Insert OD
2.6.6 auto The Autofill Insert OD setting controls whether Spectre Cloud automatically suggest...
2.6.7 Auto-Repeat Insert Type and Size
2.6.7 auto These two auto-suggestions are simply to speed up the data-entry process. Typicall...
2.6.8 Ring finger 5/16 rule difference calculator
2.6.8 auto The Ring finger 5/16 rule difference calculator setting controls whether Spectre Cl...
2.6.9 Autofill Cut to Cut measurement based on insert type/size
2.6.9 setting The Autofill Cut to Cut auto-suggestion calculates a spec sheet's Cut to Cut (C)...
2.6.10 Layout Suggestions
2.6.10 auto The Auto-Suggest Layouts will display an additional input in the Arsenal page. A ...