Advanced Search
Search Results
351 total results found
2.3.2 Initial pitch inside the total oval — Edge vs. Center & Pitch Included Yes/No
2.3.2 oval When drilling an oval hole, Spectre Cloud needs a reference point from which to calculate the initial pitch of that hole. Because an oval opening has width — unlike a round hole, which has a single center point — there are two valid ways to defin...
2.3.3 Oval Width Calculator — Bit Size, Decimal, or Difference input method
2.3.3 oval When calculating an oval thumb hole, Spectre Cloud needs to know the oval width — the final size of the opening the bowler's thumb will sit in. This setting controls how you input that measurement. There are three options: Oval Width (Bit Size), ...
2.3.5 Oval Cut 'Move' Direction — V/H, H only, V only, or None
2.3.5 oval The Oval Cut Move Direction setting controls which directional components Spectre Cloud calculates and displays when outputting oval cut values. Depending on your drill press type and how you cut ovals, you may work with both vertical and horizon...
2.3.6 Flip V/H on oval cuts — matching your drill press DRO display order
2.3.6 oval The Flip V/H on oval cuts setting controls the display order of the vertical and horizontal values in the oval cut cards shown by the Spectre Cloud oval calculator. This setting should match the order your drill press digital readout (DRO) displa...
2.4.1 Does your machine display Right Pitch Positive? (YES / NO)
Does your machine display Right Pitch Positive? (YES / NO) 2.4.1 calibration Different drill presses use different sign conventions when displaying pitch values — some treat right pitch as positive, others treat it as negative. This setting tells Spectr...
2.4.2 Does your machine display Forward Thumb Pitch Positive? (YES / NO)
Does your machine display Forward Thumb Pitch Positive? (YES / NO) 2.4.2 calibration Just as drill presses vary in how they represent lateral (right/left) pitch direction, they also differ in how they display forward and reverse thumb pitch. This settin...
2.4.3 Display +/- in pitch tiles — showing direction arrows to avoid errors
Display +/- in pitch tiles — showing direction arrows to avoid errors 2.4.3 calibration Even with sign conventions correctly configured in 2.4.1 and 2.4.2, a raw + or - symbol on a pitch tile can be easy to miss at a glance — especially under shop light...
2.4.4 Matching Spectre output to your specific drill press brand/model
Matching Spectre output to your specific drill press brand/model 2.4.4 TIP calibration Spectre Cloud includes a drill press brand and model selector that automatically configures the pitch sign convention and axis orientation settings to match your mac...
2.5.1 Default Layout Type — VLS, 2LS, PAL (Mo Pinel), or NONE
Default Layout Type — VLS, 2LS, PAL (Mo Pinel), or NONE 2.5.1 layout The Default Layout Type setting controls which layout system Spectre Cloud pre-selects when a new spec sheet is created. Rather than choosing a layout method from scratch every time, y...
2.5.1.1 VLS — Storm system for bowlers using thumb
VLS — Storm system for bowlers using thumb 2.5.1a layout The VLS (Versatile Layout System) is a ball layout method developed by Storm Bowling that determines pin and mass bias placement using a bowler's track, PAP (Positive Axis Point), and a small set ...
2.5.1.2 2LS — Storm system for two-handed bowlers
2LS — Storm system for two-handed bowlers 2.5.1b layout The 2LS (Two-Layout System) is a ball layout method developed by Storm Bowling specifically to address the unique PAP location and track profile of two-handed bowlers. Where VLS was designed with t...
2.5.1.3 PAL / Dual Angle system
PAL / Dual Angle system 2.5.1c layout The PAL (Performance Axis Layout) system — referred to in Spectre Cloud as Dual Angle — is a ball layout method that uses three measured values to precisely define pin and mass bias placement relative to a bowler's ...
2.5.1.4 NONE — Manual layout entry
NONE — Manual layout entry 2.5.1d layout When the None layout type is selected in Spectre Cloud, no layout system is applied to the spec sheet. Instead of being guided through a structured set of layout inputs, the driller enters layout information free...
2.5.2 Default Dual Angle Degree Increments — 1° vs. 5°
Default Dual Angle Degree Increments — 1° vs. 5° 2.5.2 layout When entering drilling angle and VAL angle values in a Dual Angle (PAL) layout, Spectre Cloud lets you choose the degree increment used when adjusting angle inputs — either 1° for fine-graine...
2.6.1 Overview — why leaving all Auto-Suggestions ON saves time
Overview — why leaving all Auto-Suggestions ON saves time 2.6.1 TIP auto Spectre Cloud includes a suite of auto-suggestion features that automatically populate recommended values across spec sheets as you work — finger and thumb sizes, pitches, spans,...
2.6.2 Pitch Suggestion — auto forward pitch based on hand flexibility
Pitch Suggestion — auto forward pitch based on hand flexibility 2.6.2 auto The Pitch Suggestion setting controls whether Spectre Cloud automatically recommends a forward thumb pitch value based on the bowler's recorded hand flexibility. When enabled, th...
2.6.3 Auto-CLT — lateral pitch of fingers based on CLT chart
Auto-CLT — lateral pitch of fingers based on CLT chart 2.6.3 auto The Auto-CLT setting controls whether Spectre Cloud automatically suggests a lateral pitch value for the finger holes based on the bowler's Center Line Transformation (CLT) measurement. W...
2.6.4 Auto-Invert standard lateral pitches when changing from RH to LH
Auto-Invert standard lateral pitches when changing from RH to LH 2.6.4 auto The Auto-Invert setting controls whether Spectre Cloud automatically mirrors lateral pitch values when a spec sheet is switched between a right-handed (RH) and left-handed (LH) ...
2.6.5 Autofill Bridge — auto standard bridge (1/4" Fingertip, 3/8" conventional)
Autofill Bridge — auto standard bridge (1/4" Fingertip, 3/8" conventional) 2.6.5 auto The Autofill Bridge setting controls whether Spectre Cloud automatically populates the bridge measurement field on a new spec sheet based on the bowler's grip style. W...
2.6.6 Autofill Insert OD — auto drill bit size per insert type and grip
Autofill Insert OD — auto drill bit size per insert type and grip 2.6.6 auto The Autofill Insert OD setting controls whether Spectre Cloud automatically suggests the correct drill bit size for a bowler's finger holes based on their insert type and grip ...