Skip to main content

Recently Updated Pages

Suggested layouts ( based on axis rotation )

Layout

Here a couples suggestions of layouts based on axis rotation . For bowlers have  ( 0-30 degrees ...

Updated 11 months ago by JP Côté

Basic Layout

Layout

The basic 60-degree layout in relation to the CG is ideal for beginner bowlers and applies only...

Updated 11 months ago by JP Côté

Here is the understanding of the 3 phases of the hook that the ball must go through!

Ball Motion

1. -Phase 1 of the lane is the front part, which goes from the foul line to 30 feet. -Phase 2...

Updated 1 year ago by JP Côté

Ball Speed and Rev Rate

The Bowlers

1.All bowlers are different from one another. There are five categories of bowlers based on the s...

Updated 1 year ago by JP Côté

Axis Tilt

The Bowlers

Bowling axis tilt is the upward or downward angle of the ball's axis of rotation relative to the ...

Updated 1 year ago by JP Côté

Axis Rotation

The Bowlers

There are three types of axis of rotation your player can end up on... 1: ( 0-30 degrees )    10...

Updated 1 year ago by JP Côté

Finding and Measuring the PAP ( Positive Axis Point )

The Bowlers

1. 2. 3. 4. 5. 6.    

Updated 1 year ago by JP Côté

Here are the 5 important things to mention when identifying the bowlers.

The Bowlers 5 STATS TO GATHER

. PAP ( Positive Axis Point) . Axis Rotation  . Axis tilt . Speed . Rev Rate

Updated 1 year ago by JP Côté

Step-by-step guide

Fitting Finger Tip Fitting

Following these steps will ensure a proper fit Warm up your hand ( either massage or bowl) Me...

Updated 1 year ago by JP Côté

Option #2 - Drilling the thumb hole first

Drilling Drilling Options

1 1)    Draw center line and midline of grip    2)    Dividing the span of the middle finger in ...

Updated 1 year ago by Art

How to Setting your Spectre Cloud

Settings

1.Click on "Settings"located on top to the Spectre cloud. Then you get acces to the menu of "S...

Updated 1 year ago by JP Côté

Process

Drilling Preparation for drilling

There are 3 separate processes that have to be achieved in order to drill a ball for a bowler. F...

Updated 1 year ago by Art

Option #1 – Drilling the finger holes first

Drilling Drilling Options

1)      Draw centre line and midline of grip 2)      Dividing the span of the middle finger in h...

Updated 1 year ago by Art

Drilling an Oval Thumb

Fitting Finger Tip Fitting

3 Measurements Smallest - Starting bit Largest - Width of oval Oval direction ...

Updated 1 year ago by Frankie

Step-by-step guide

Fitting Conventional Fitting

Following these steps will ensure a proper fit Warm up the hand, massage/bowl Measure the MID...

Updated 1 year ago by Admin

Ultimate

Fitting Inserts & Slugs

Ultimate Powerlift/Oval Powerlift: 1/4" FORWARD pitch in the grip Compensate 1/4" REVERSE ...

Updated 1 year ago by Chris Esdon

Jopo

Fitting Inserts & Slugs

Jopo Power Flat/Oval Power Flat: 1/4" FORWARD pitch in the grip Compensate 1/4" REVERSE wh...

Updated 1 year ago by Chris Esdon

Vise

Fitting Inserts & Slugs

Vise Powerlift/Semi Powerlift: 1/4" FORWARD pitch in the grip Compensate 1/4" REVERSE wh...

Updated 1 year ago by Chris Esdon

Turbo

Fitting Inserts & Slugs

Turbo Quad                                                                                      ...

Updated 1 year ago by Chris Esdon

Contour

Fitting Inserts & Slugs

Contour Oval Oval: 0 pitch in the grip No compensation needed Contour Semi Cerise ...

Updated 1 year ago by Chris Esdon