04 Spec Sheets _origianl

4.1.1 Acronyms Used in Spectre Cloud

📐 Acronyms Used in Spectre Cloud Beyond the three primary span type acronyms, Spectre Cloud uses...

4.1.2 Span types explained: F, C, O, H

4.1.2 concept The span type setting on a Spectre Cloud spec sheet defines the measurement conv...

4.1.3 Grip type definitions: Finger Tip vs. Conventional

4.1.3 concept A bowler's grip type defines how deeply their fingers are inserted into the ball...

4.1.4 Pitch terminology

4.1.4 concept Pitch is the angle at which a finger or thumb hole is drilled relative to the ba...

4.1.5 Bridge: standard bridge sizes and their purpose

4.1.5 concept The bridge is the distance between the near edges of the middle and ring finger ...

4.1.6 Insert OD: drill bit sizing for STD and VACU grips

4.1.6 concept When drilling finger holes for bowlers who use inserts, the drill bit must match...

4.2.1 Creating a blank spec sheet for a bowler

1. Access Bowler Profiles Click "Bowlers" to open the list of bowler profiles in Spectre Prosh...

4.2.2 Naming a spec sheet

4.2.2 step-by-step When you create a new spec sheet, Spectre Cloud lets you give it a plain-En...

4.2.3 Selecting grip type on the spec sheet

1. Access Bowler Section Click "Bowlers" to open the bowler management section in Spectre Pr...

4.2.4 How to identify the type of grip from measurement sheet

4.2.4 step-by-step Before entering span and pitch measurements, you need to identify which gri...

4.2.5 Cloning a spec sheet

4.2.5 TIP step-by-step When you need to make an adjustment to an existing fit, and you want ...

4.2.6 Printing a spec sheet

4.2.6 TIP step-by-step Once a spec sheet is complete, you can print it directly from Spectre...

4.2.7 Cloning an existing spec sheet

4.2.7 TIP step-by-step 1. Open Bowler Profile Select a bowler you would like to clone the...

4.3.1 Entering finger hole size (ring and middle fingers)

1. Select Customer Account Click and select the bowler 2. Hole size Click on hole size ...

4.3.2 Entering span measurements, F, C, O, H

4.3.2 step-by-step Span measurements define the distance between the thumb hole and each finge...

4.3.3 Inputing Vertical and Lateral pitch for fingers

4.3.3 measurement Finger pitch is entered directly into the pitch tiles surrounding each finge...

4.3.4 CLT (Corrected lateral tilt) angle and its effect on lateral pitch

CLT (Corrected lateral tilt) angle and its effect on lateral pitch ...

4.3.5 How to input a finger oval measurement (no inserts)

How to input a finger oval measurement (no inserts) For bowlers...

4.3.6 Ring Finger 5/16" rule — auto and manual calculation

Ring Finger 5/16" rule — auto and manual calculation When ...

4.3.7 Insert type and size: STD vs. VACU, selecting drill bit OD

Insert type and size: STD vs. VACU, selecting drill bit OD 4.3.7 measurement Once span, pi...

4.4.1 Selecting "Round" thumb hole on the spec sheet

Selecting "Round" thumb hole on the spec sheet 4.4.1 thumb The thumb hole is the largest h...

4.4.2 Entering thumb hole size

Entering thumb hole size 4.4.2 thumb Once the thumb hole shape is selected, the spec sheet...

4.4.3 Entering bowler's span (Full and Cut to Cut)

Entering bowler's span (Full and Cut to Cut) 4.4.3 thumb This page walks through the pr...

4.4.4 Entering vertical and lateral pitch for thumb

Entering vertical and lateral pitch for thumb Thumb pitch works on the same principl...

4.4.5 Installing a pre-drilled thumb insert

Installing a pre-drilled thumb insert 4.4.5 thumb A pre-drilled thumb insert arrives from ...

4.5.1 Selecting "Oval" thumb hole on the spec sheet

Selecting "Oval" thumb hole on the spec sheet 4.5.1 KEY oval Drilling an oval thumb h...

4.5.2 Entering Starting Bit, Oval Width, Oval Degree, and Taper

Entering Starting Bit, Oval Width, Oval Degree, and Taper 4.5.2 oval TODO — write this page.

4.5.3 How the system calculates the oval cut from your inputs

How the system calculates the oval cut from your inputs 4.5.3 oval Once the four oval inpu...

4.5.4 Entering thumb oval span and pitch information

Entering thumb oval span and pitch information 4.5.4 oval For most spec sheets, span is me...