5.2 — Method A: V/H Mo...

5.2.1 Setting up: Oval Cut Direction = V/H in Settings

Setting up: Oval Cut Direction = V/H in Settings 5.2.1 CALC oval method Before using the...

5.2.2 Entering Starting Bit and Oval Width — Bit Size mode

Entering Starting Bit and Oval Width — Bit Size mode 5.2.2 oval method When using the Oval...

5.2.3 Entering Starting Bit and Oval Width — Decimal mode

Entering Starting Bit and Oval Width — Decimal mode 5.2.3 oval method When using the Oval ...

5.2.4 Reading the DIFF (decimal difference) auto-calculation

Reading the DIFF (decimal difference) auto-calculation 5.2.4 oval method Whenever you ente...

5.2.5 Adding oval cut rows using the + button

Adding oval cut rows using the + button 5.2.5 oval method The Oval Calculator in Spectre C...

5.2.6 Entering V and H cut values (positive and negative)

Entering V and H cut values (positive and negative) 5.2.6 oval method When recording oval ...

5.2.7 Confirming cuts using the arrow-down key

Confirming cuts using the arrow-down key 5.2.7 oval method After entering V and H cut valu...

5.2.8 Worked example: full V/H oval from start to finish

Worked example: full V/H oval from start to finish 5.2.8 TIP example This page walks thr...

5.1.1 What is an oval thumb hole and why is it used?

5.1.2 Oval terminology: Starting Bit, Oval Width, Oval Degrees, Taper

5.1.3 Vertical cut (V) vs. Horizontal cut (H) — what they mean physically

5.1.4 How oval degree affects pitch inside the oval

5.2.1 Setting up: Oval Cut Direction = V/H in Settings

5.2.2 Entering Starting Bit and Oval Width — Bit Size mode

5.2.3 Entering Starting Bit and Oval Width — Decimal mode

5.2.4 Reading the DIFF (decimal difference) auto-calculation

5.2.5 Adding oval cut rows using the + button

5.2.6 Entering V and H cut values (positive and negative)

5.2.7 Confirming cuts using the arrow-down key

5.2.8 Worked example: full V/H oval from start to finish

5.3.1 Setting up: Oval Cut Direction = H in Settings

5.3.2 When to use H-only mode and which drill presses it suits

5.3.3 Entering H-only cut values and reading output

5.3.4 Worked example: H-only oval

5.4.1 Setting up: Oval Cut Direction = V in Settings

5.4.2 When to use V-only mode

5.4.3 Entering V-only cut values and reading output

5.5.1 Setting up: Oval Cut Direction = NONE in Settings

5.5.2 Using the oval cut chart to determine cuts manually

5.5.3 When NONE mode is preferable (experienced fitters, custom setups)

5.6.1 EDGE method explained — how pitch is placed at edge of oval

5.6.2 CENTER method explained — how pitch is placed at center of oval

5.6.3 EDGE with and without Add Pitch Thumb — comparison

5.6.4 CENTER with and without Add Pitch Thumb — comparison

5.6.5 Choosing EDGE vs. CENTER: which method fits which bowler?

5.6.6 1° vs. 5° Oval Degree increments and their precision impact

5.7.1 Using "Flip V/H on oval cuts" to match your machine's axis

5.7.2 Worked example: how flipping V/H changes the output numbers

5.2 — Method A: V/H Mode (Most Common)

5.2.1 Setting up: Oval Cut Direction = V/H in Settings

5.2.2 Entering Starting Bit and Oval Width — Bit Size mode

5.2.3 Entering Starting Bit and Oval Width — Decimal mode

5.2.4 Reading the DIFF (decimal difference) auto-calculation

5.2.5 Adding oval cut rows using the + button

5.2.6 Entering V and H cut values (positive and negative)

5.2.7 Confirming cuts using the arrow-down key

5.2.8 Worked example: full V/H oval from start to finish

Search Results