Skip to main content

2.2.5 Insert Installation — STD vs. VACU grip default

Insert Installation — STD vs. VACU grip default

2.2.5   default

TODO — write this page.

```html

The Insert Installation settingdefault controls which insert installation method is pre-selected when creating a new spec sheet.sheet Spectre— Cloud supports two methods:either STD (Standard)standard gluedglued) installation andor VACU Grip suction-based installation.(vacuum-style). Setting the correct default for your shop means your drillers spend less time adjusting this field on every new sheet.

🔌🔩 STD vs. VACU Grip — What's the Difference?

Both methods describe how finger inserts are secured inside the drilled finger holes. The key distinction is whetherin adhesive or suction holdshow the insert is held in place:place and how the finger hole is prepared:d

  • ✅ STD (Standard) — insertsthe arefinger hole is drilled to a single diameter and the insert is glued directly into the finger holeplace using bowling ball insert adhesive. The most widely used installation method across pro shops worldwide. Once installed, inserts are semi-permanent and require a drill or pick tool to remove and replace.
  • ✅ VACU Grip — a two-tier drilling technique where the finger hole is drilled in two stages: the upper portion is bored larger than the insert's outer diameter, and the lower portion is drilled tighter so the insert is glued in only at the base. Because the insert is only secured at the bottom, the rubber body is free to expand outward when the bowler inserts their finger, creating a snug, adaptive fit that accommodates finger swelling during play. The insert used must be several sizes smaller than the bowler's standard fingertip size to allow for this expansion.

Note: The VACU Grip method requires a specific two-stage drilling sequence at the press. See Mark Buffa's full walkthrough on the Spectre YouTube channel: How To Drill For A Vacu Fit!

⚙️ Changing the Insert Installation Default

  1. Open Spectre Cloud at cloud.spectrebowling.com and log in.
  2. Select Settings from the menu.
  3. Navigate to the System Defaults section.
  4. Locate the Insert Installation field and select either STD or VACU.
  5. Changes are heldsaved in place by a vacuum suction fit rather than glue. Bowlers can remove and re-seat their own inserts between sessions without tools. Requires VACU-compatible inserts and a properly sized hole for the vacuum seal to function correctly.automatically.

Note: This setting controls only the default pre-selection on new spec sheets. The installation method can always be changed on aany per-bowler,individual per-spec sheet basis without affecting your shop default.

⚙️ Changing the Insert Installation Default

  1. Open Spectre Cloud at cloud.spectrebowling.com and log in.
  2. Click your pro shop name in the top-right corner to open the Profile menu.
  3. Select Settings from the dropdown.
  4. Navigate to the Spec Sheet Defaults section.
  5. Locate the Insert Installation field and select either STD or VACU Grip.
  6. Click Save to apply the change.

image.png

🎳 Which Default Should You Choose?

Shop Situation Recommended Default Reason
Most pro shops — general clientele STD Standard glue installation is the industry norm for the majority of fittings
Shop specialising in VACU Grip fittings VACU Grip Saves time if VACU is your predominant installation method
Mixed clientele — both methods used regularly STD STD is more common; override to VACU onlyon a per-sheet basis when needed per sheet

📋 Important: Select Insert Type Before Insert Size

When entering insert details on a spec sheet, always select the Insert Type first, then the Insert Size. If the Auto Insert OD suggestion is enabled in your settings, Spectre will automatically populate the outer diameter field based on the insert type and size selected.

image.png

image.png

🖨️ How It Appears on a Spec Sheet

The selected installation method is recorded on every spec sheet and appears in the insert details section. This ensures your shop's drilling history accurately reflects how each ball was fitted — useful when a bowler returns for an insert replacement or a re-drill.

  • ✅ The installation method is saved with the spec sheet and visible in historical records.
  • ✅ Printed and exported spec sheets include the installation method field.
  • ❌ Changing the shop default does not retroactively update the installation method on existing spec sheets.

Tip: If you stock and sell VACU Grip inserts in your shop, it may be worthinserts, noting the installation method clearly on printed spec sheets is good practice — bowlers who use VACU inserts often need to know their exact insert size when purchasing replacements.

```

Back to top